Rosemount 848T Especificaciones Pagina 28
- Pagina / 136
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
20
Reference Manual
00809-0100-4697, Rev GA
Section 3: Configuration
November 2014
Configuration
3.2 Configuration
3.2.1 Standard
Each FOUNDATION
™
fieldbus configuration tool or host system has a different way of displaying
and performing configurations. Some will use Device Descriptions (DDs) and DD Methods to
make configuration and displaying of data consistent across host platforms.
Unless otherwise specified, the 848T will be shipped with the following configuration (default):
Table 3-1. Standard Configuration Settings
Refer to that systems documentation to perform configuration changes using a F
OUNDATION
fieldbus host or configuration tool.
Note
To make configuration changes, ensure that the block is Out of Service (OOS) by setting the
MODE_BLK.TARGET to OOS, or set the SENSOR_MODE to Configuration.
3.2.2 Transmitter configuration
The transmitter is available with the standard configuration setting. The configuration settings
and block configuration may be changed in the field with the Emerson Process Management
Systems DeltaV
™
, with AMS
®
inside, or other FOUNDATION fieldbus host or configuration tool.
3.2.3 Custom configuration
Custom configurations are to be specified when ordering.
3.2.4 Methods
For FOUNDATION fieldbus hosts or configuration tools that support device description (DD)
methods, there are two configuration methods available in the transducer block. These
methods are included with the DD software.
Sensor Configuration
Sensor Input Trim (user input trim)
See the host system documentation for information on running DD methods from the host
system. If the F
OUNDATION fieldbus host or configuration tool does not support DD methods,
refer to “Block configuration” on page 25 for information on how to modify sensor
configuration parameters.
Sensor Type
(1)
(1) For all eight sensors
Type J Thermocouple
Damping
(1)
5 seconds
Measurement Units
(1)
°C
Output
(1)
Linear with Temperature
Line Voltage Filter
(1)
60 Hz
Temperature Specific Blocks
• Transducer Block (1)
FOUNDATION fieldbus Function Blocks
• Analog Input (8)
•Multiple Analog Input (2)
• Input Selector (4)
- Transmitter with FOUNDATION 1
- fieldbus 1
- Transmitter with F 3
- Title Page 4
- 1Section 1: Introduction 5
- 2Section 2: Installation 5
- 3Section 3: Configuration 5
- AAppendix A: Reference Data 6
- DAppendix D: Function Blocks 8
- Section 1 Introduction 9
- 00809-0100-4697, Rev GA 10
- November 2014 10
- OUNDATION fieldbus Technology 10
- 1.3 Service support 11
- Section 1: Introduction 12
- Introduction 12
- Section 2 Installation 13
- 2-in. screws 14
- 2.3 Wiring 16
- RTD or ohm inputs 17
- Analog inputs 17
- 2.4 Grounding 19
- Shielded wire 20
- Grounded thermocouple inputs 21
- Analog device inputs 21
- 2.5 Switches 22
- 2.6 Tagging 22
- Transmitter tag 23
- Sensor tag 23
- 2.7 Installation 24
- 2.7.2 Using conduit entries 25
- Section 2: Installation 26
- Section 3 Configuration 27
- 3.2 Configuration 28
- 3.2.5 Alarms 29
- 3.2.6 Damping 29
- Typical profiling application 31
- OUNDATION fieldbus 33
- Section 3: Configuration 34
- Number Parameter Description 34
- OUNDATION 35
- How to use PlantWeb Alarm 39
- 3.4.3 PlantWeb alerts 40
- MAINT_ALARMS 41
- Advisory alarms 42
- RECOMMENDED_ACTION 43
- FD failed alarms 44
- Configuration 45
- FD CHECK ALARMS 47
- 3.4.7 Transducer blocks 49
- Transducer block errors 50
- Transducer block modes 50
- Automatic (Auto) 51
- Out of Service (OOS) 51
- 4.4.2 Resource block 64
- Appendix A Reference Data 65
- OUNDATION fieldbus parameters 66
- A.3 Function blocks 67
- A.4.1 Stability 68
- A.4.2 Self calibration 68
- A.4.3 Vibration effect 68
- A.4.5 Accuracy 68
- A.4.8 Analog sensors 4–20mA 69
- Reference Data 70
- Examples 71
- A.5 Dimensional drawings 72
- A.5.1 Mounting options 74
- A.6 Ordering information 75
- Approvals 77
- B.3.2 Canada 78
- B.4 Europe 79
- B.5 International 81
- B.5.1 Brazil 83
- B.5.2 China 84
- B.5.3 Japan 86
- B.6 Combinations 87
- B.8 Additional Certifications 88
- B.10 Installation drawings 90
- Product Certificates 91
- Appendix C FOUNDATION 99
- Technology 99
- C.3 Device descriptions 100
- C.4 Block operation 101
- C.5 Network communication 101
- C.5.1 LAS 102
- C.5.2 Addressing 103
- C.5.3 Scheduled transfers 104
- C.5.4 Unscheduled transfers 105
- OUNDATION Fieldbus Technology 106
- Appendix D Function Blocks 107
- Reference Manual 108
- Appendix D: Function Blocks 108
- Table 3-5 on page 11 108
- D.1.1 Functionality 110
- Filtering 111
- Signal conversion 111
- Indirect 111
- Indirect square root 112
- Block errors 112
- Alarm detection 113
- Status handling 114
- Advanced features 114
- Application information 114
- D.2.1 Functionality 118
- D.3.1 Functionality 125
- Block execution 127
- AVG_USE = 6 129
- Numerics 131
Relacionado con productos y manuales para De medición, control y control Rosemount 848T
(36 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.024 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales