Rosemount 848T Especificaciones Pagina 83
- Pagina / 136
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
75
Reference Manual
00809-0100-4697, Rev GA
Appendix B: Product Certifications
November 2014
Product Certificates
Special Conditions of Safe Use:
1. The component must be installed in a suitable component certified enclosure
that provides a degree of protection of at least IP54 and meets the relevant
material and environmental requirements of EN 60079-0:2006 and EN
60079-15:2005.
2. Provision must be made, external to the apparatus, to ensure the rated voltage of
the apparatus supply is not exceeded by transient disturbances of more than
40%.
3. The electrical circuit is connected directly to earth; this must be taken into
account when installing the apparatus.
B.5.1 Brazil
I2 INMETRO Intrinsic Safety
Certificate: NCC 12.1156X
Standards: ABNT NBR IEC 60079-0:2008 Versão corrigida 2011, ABNT NBR IEC
60079-11:2009, ABNT NBR IEC 60079-26:2008 Versão corrigida 2009, ABNT
NBR IEC 60079-27:2010
Markings: Ex ia IIC T4 (-50 °C ≤ T
a
≤ +60 °C)
Special Conditions of Safe Use:
1. The equipment must be installed in an enclosure that provides a degree of
protection of at least IP20 and which is appropriate to the application specified in
ABNT NBR IEC60079-0.
2. The equipment is not capable of withstanding the dielectric strength test of
500V according to item 6.3.12 of ABNT NBR IEC60079-1, this should be
considered in the installation, see installation manual.
IB INMETRO Intrinsic Safety
Certificate: NCC 12.1156X
Standards: ABNT NBR IEC 60079-0:2008 Versão corrigida 2011, ABNT NBR IEC
60079-11:2009, ABNT NBR IEC 60079-26:2008 Versão corrigida 2009, ABNT
NBR IEC 60079-27:2010
Markings: Ex ia IIC T4 (-50 °C ≤ T
a
≤ +60 °C)
Table B-6. INMETRO-2 Entity Parameters
FISCO (Input)
Sensor Field Terminal
(Output)
U
i
= 30 Vdc U
o
= 12.5 Vdc
I
i
= 300 mA I
o
= 4.8 mA
P
i
= 1.3 W P
o
= 15 mW
C
i
= 2.1 nF C
o
= 1.2 mF
L
i
= 0 L
o
= 1 H
- Transmitter with FOUNDATION 1
- fieldbus 1
- Transmitter with F 3
- Title Page 4
- 1Section 1: Introduction 5
- 2Section 2: Installation 5
- 3Section 3: Configuration 5
- AAppendix A: Reference Data 6
- DAppendix D: Function Blocks 8
- Section 1 Introduction 9
- 00809-0100-4697, Rev GA 10
- November 2014 10
- OUNDATION fieldbus Technology 10
- 1.3 Service support 11
- Section 1: Introduction 12
- Introduction 12
- Section 2 Installation 13
- 2-in. screws 14
- 2.3 Wiring 16
- RTD or ohm inputs 17
- Analog inputs 17
- 2.4 Grounding 19
- Shielded wire 20
- Grounded thermocouple inputs 21
- Analog device inputs 21
- 2.5 Switches 22
- 2.6 Tagging 22
- Transmitter tag 23
- Sensor tag 23
- 2.7 Installation 24
- 2.7.2 Using conduit entries 25
- Section 2: Installation 26
- Section 3 Configuration 27
- 3.2 Configuration 28
- 3.2.5 Alarms 29
- 3.2.6 Damping 29
- Typical profiling application 31
- OUNDATION fieldbus 33
- Section 3: Configuration 34
- Number Parameter Description 34
- OUNDATION 35
- How to use PlantWeb Alarm 39
- 3.4.3 PlantWeb alerts 40
- MAINT_ALARMS 41
- Advisory alarms 42
- RECOMMENDED_ACTION 43
- FD failed alarms 44
- Configuration 45
- FD CHECK ALARMS 47
- 3.4.7 Transducer blocks 49
- Transducer block errors 50
- Transducer block modes 50
- Automatic (Auto) 51
- Out of Service (OOS) 51
- 4.4.2 Resource block 64
- Appendix A Reference Data 65
- OUNDATION fieldbus parameters 66
- A.3 Function blocks 67
- A.4.1 Stability 68
- A.4.2 Self calibration 68
- A.4.3 Vibration effect 68
- A.4.5 Accuracy 68
- A.4.8 Analog sensors 4–20mA 69
- Reference Data 70
- Examples 71
- A.5 Dimensional drawings 72
- A.5.1 Mounting options 74
- A.6 Ordering information 75
- Approvals 77
- B.3.2 Canada 78
- B.4 Europe 79
- B.5 International 81
- B.5.1 Brazil 83
- B.5.2 China 84
- B.5.3 Japan 86
- B.6 Combinations 87
- B.8 Additional Certifications 88
- B.10 Installation drawings 90
- Product Certificates 91
- Appendix C FOUNDATION 99
- Technology 99
- C.3 Device descriptions 100
- C.4 Block operation 101
- C.5 Network communication 101
- C.5.1 LAS 102
- C.5.2 Addressing 103
- C.5.3 Scheduled transfers 104
- C.5.4 Unscheduled transfers 105
- OUNDATION Fieldbus Technology 106
- Appendix D Function Blocks 107
- Reference Manual 108
- Appendix D: Function Blocks 108
- Table 3-5 on page 11 108
- D.1.1 Functionality 110
- Filtering 111
- Signal conversion 111
- Indirect 111
- Indirect square root 112
- Block errors 112
- Alarm detection 113
- Status handling 114
- Advanced features 114
- Application information 114
- D.2.1 Functionality 118
- D.3.1 Functionality 125
- Block execution 127
- AVG_USE = 6 129
- Numerics 131
Relacionado con productos y manuales para De medición, control y control Rosemount 848T
(36 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.030 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales