Rosemount 848T Especificaciones Pagina 63
- Pagina / 136
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
55
Reference Manual
00809-0100-4697, Rev GA
Section 4: Operation and Maintenance
November 2014
Operation and Maintenance
4.3.3 Resetting the configuration (RESTART)
There are two types of restarts available in the Resource Block. The following section outlines
the usage for each of these. For further information, see RESTART in Table 3-2 on page 3-25.
Restart processor (cycling)
Performing a Restart Processor has the same effect as removing power from the device and
reapplying power.
Restart with defaults
Performing a Restart with Defaults resets the static parameters for all of the blocks to their initial
state. This is commonly used to change the configuration and/or control strategy of the device,
including any custom configurations done at the Rosemount factory.
4.4 Troubleshooting
4.4.1 FOUNDATION fieldbus
Symptom Possible cause Corrective action
Device does not show
up in the live list
Network configuration
parameters are incorrect
Set the network parameters of the LAS (host system) according to
the FF Communications Profile
ST: 8
MRD: 4
DLPDU PhLO: 4
MID: 7
TSC: 4 (1 ms)
T1: 96000 (3 seconds)
T2: 9600000 (300 seconds)
T3: 480000 (15 seconds)
Network address is not in
polled range
Set first Unpolled Node and Number of UnPolled Nodes so that the
device address is within range
Power to the device is
below the 9 VDC minimum
Increase the power to at least 9V
Noise on the power /
communication is too high
Verify terminators and power conditioners are within specification
Verify that the shield is properly terminated and not grounded at
both ends. It is best to ground the shield at the power conditioner
Device that is acting
as a LAS does not send
out CD
LAS Scheduler was not
downloaded to the Backup
LAS device
Ensure that all of the devices that are intended to be a Backup LAS
are marked to receive the LAS schedule
All devices go off live
list and then return
Live list must be
reconstructed by Backup
LAS device
Current link setting and configured links settings are different. Set
the current link setting equal to the configured settings.
- Transmitter with FOUNDATION 1
- fieldbus 1
- Transmitter with F 3
- Title Page 4
- 1Section 1: Introduction 5
- 2Section 2: Installation 5
- 3Section 3: Configuration 5
- AAppendix A: Reference Data 6
- DAppendix D: Function Blocks 8
- Section 1 Introduction 9
- 00809-0100-4697, Rev GA 10
- November 2014 10
- OUNDATION fieldbus Technology 10
- 1.3 Service support 11
- Section 1: Introduction 12
- Introduction 12
- Section 2 Installation 13
- 2-in. screws 14
- 2.3 Wiring 16
- RTD or ohm inputs 17
- Analog inputs 17
- 2.4 Grounding 19
- Shielded wire 20
- Grounded thermocouple inputs 21
- Analog device inputs 21
- 2.5 Switches 22
- 2.6 Tagging 22
- Transmitter tag 23
- Sensor tag 23
- 2.7 Installation 24
- 2.7.2 Using conduit entries 25
- Section 2: Installation 26
- Section 3 Configuration 27
- 3.2 Configuration 28
- 3.2.5 Alarms 29
- 3.2.6 Damping 29
- Typical profiling application 31
- OUNDATION fieldbus 33
- Section 3: Configuration 34
- Number Parameter Description 34
- OUNDATION 35
- How to use PlantWeb Alarm 39
- 3.4.3 PlantWeb alerts 40
- MAINT_ALARMS 41
- Advisory alarms 42
- RECOMMENDED_ACTION 43
- FD failed alarms 44
- Configuration 45
- FD CHECK ALARMS 47
- 3.4.7 Transducer blocks 49
- Transducer block errors 50
- Transducer block modes 50
- Automatic (Auto) 51
- Out of Service (OOS) 51
- 4.4.2 Resource block 64
- Appendix A Reference Data 65
- OUNDATION fieldbus parameters 66
- A.3 Function blocks 67
- A.4.1 Stability 68
- A.4.2 Self calibration 68
- A.4.3 Vibration effect 68
- A.4.5 Accuracy 68
- A.4.8 Analog sensors 4–20mA 69
- Reference Data 70
- Examples 71
- A.5 Dimensional drawings 72
- A.5.1 Mounting options 74
- A.6 Ordering information 75
- Approvals 77
- B.3.2 Canada 78
- B.4 Europe 79
- B.5 International 81
- B.5.1 Brazil 83
- B.5.2 China 84
- B.5.3 Japan 86
- B.6 Combinations 87
- B.8 Additional Certifications 88
- B.10 Installation drawings 90
- Product Certificates 91
- Appendix C FOUNDATION 99
- Technology 99
- C.3 Device descriptions 100
- C.4 Block operation 101
- C.5 Network communication 101
- C.5.1 LAS 102
- C.5.2 Addressing 103
- C.5.3 Scheduled transfers 104
- C.5.4 Unscheduled transfers 105
- OUNDATION Fieldbus Technology 106
- Appendix D Function Blocks 107
- Reference Manual 108
- Appendix D: Function Blocks 108
- Table 3-5 on page 11 108
- D.1.1 Functionality 110
- Filtering 111
- Signal conversion 111
- Indirect 111
- Indirect square root 112
- Block errors 112
- Alarm detection 113
- Status handling 114
- Advanced features 114
- Application information 114
- D.2.1 Functionality 118
- D.3.1 Functionality 125
- Block execution 127
- AVG_USE = 6 129
- Numerics 131
Relacionado con productos y manuales para De medición, control y control Rosemount 848T
(36 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.023 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales